Our walk-in Combo
A cooler/freezer combo includes both a cooler and a freezer but shares a common wall to save money and space. They can be built with both doors opening to the exterior or with the freezer opening into the cooler which we recommend as the air temp entering the freezer will be 35F as compared to warmer temps if it opens to the exterior. We build walk-in freezers for a variety of applications including: restaurants; convenience stores, grocery stores and food storage facilities. Walls are typically 4” thick with an insulated floor in the freezer section only. They are paired with both low and medium-temp condensing units along with air & electric defrost evaporator coils to maintain appropriate temps within each room of the walk-in. Our experienced sales staff will ensure the correct combo is built to meet your cold storage needs.
Walk-In Combo Specs
Walk-in panels shall be modular in design and are to be constructed of 3 ½”, 4” or 5 ” thick prefabricated panels manufactured with 100% US made materials.
Panels to be U.L. foamed-in-place polyurethane insulation between interior and exterior metal pans that have been die-formed and gauged for uniformity. Panel perimeter shall be tongue-and-groove design with 10 lb density foam rail construction. Rails to have a ½ “ indent to assure flush finish surface with metal flange and single bulb NSF gasket. Panels shall be modular in design and connected with cam-locking fasteners to assure airtight seams and structural strength to the panels. Cam locks are lever acting with eccentric hooked locks and mating pins securely anchored in the adjacent panel to assure the ease of alignment and positive seal. Cam-lock spacing shall not exceed 48” on center. Access ports for cam locks to be covered with snap-in cap plugs.
CFC free urethane insulation shall have 97% closed cell structure. Class 1 rated urethane foam to have thermal conductivity (K-Factor) of not less than .120 BTU/hr per degree F/ inch and overall heat transfer coefficient (U-Factor) of not more than .030 BTU/hr sq ft. All foam panels to be supplied with Class 1 fire hazard insulation certified by Underwriters Laboratories as having a flame spread of 25 or less and smoke generation of 450 or less when tested in accordance with ASTM-E-84.
Panel Locking System
Assembly of walk-ins shall be accomplished by cam-locking fasteners which shall be foamed-in-place and activated by a hex wrench provided by the factory. Access ports shall be on the interior of panels to allow assembly of walk-ins from inside and shall be covered with snap caps.
Standard metal is 26 gauge embossed bright galvanized finished. U.S. made G-90 galvanized coating with a certificate of origin.
Floor panels shall be 4 ½“ thick and constructed with metal bonded to ¾” exterior grade plywood and then foamed-in-place. Standard floor finish is .040 smooth aluminum. Floors shall be designed and manufactured to support uniformly distributed stationary loads up to 700 pounds per square foot. If a floor is not required, alignment channel is provided. Channel is designed to be anchored to masonry floors and to provide a template for wall panels.
Standard door shall be overlap or in-fitting, flush design as specified. The door edge shall consist of a PVC perimeter into which the interior and exterior metal skins are secured and shall create a thermal break between metal facings. Magnetic gasket shall be dart and ridge design to allow quick replacement. Freezer doors shall have concealed heated jamb and threshold heater, easily accessible for replacement or service. Heated pressure relief vent port shall be provided on freezer applications. The door hinges shall be heavy-duty cam-lift design in bright chrome finish. Hinges shall have steel pins with nylon bushings and shall be of sufficient size and number to support twice the weight of the door. The door latch shall be made of similar materials and finish as the door hinges. The latch shall incorporate an inside safety release that complies with OSHA standards. All doors shall be self-closing without assistance when opened up to 90 degrees and shall remain open when opened above 90 degrees. The bottom of the door shall have a flexible sweep gasket.
Light fixture shall be compact vapor-proof fluorescent type, shipped loose, with a shatterproof globe cover (light bulb included). Light switch with pilot light and digital thermometer shall be factory installed and flush-mounted on the exterior of the door section. All wiring within the door section, light switch, and light fixture, to be factory installed in conduit and shall terminate at the top of the frame. Field connection by others is required for complete operation; 120 volt, 60 cycle, 1-phase. All components to be U.L. Recognized.
Testing and Approvals
- U.L. Certified Panels
- Panels Certified to NSF/ANSI Standard #7.
- Electrical and refrigeration components are Underwriters Laboratories Listed or Recognized and National Sanitation Foundation Certified.
- SGS US Testing Company, Inc. Report Number 740813-1
- Flame spread and smoke developed per UL-723, ASTM E84-95b, ANSI/NFPA No. 255, and UBC No. 8-1.
- 2007 Federal Energy Independence & Safety Act (EISA) compliant
- Los Angeles Research Report Number 25314.
- City of Los Angeles Approved Fabricator Certificate # 2055
- California Energy Commission (CEC) Title 20 compliant.
- City of Houston Fabricator’s Certificate # 772
- Oregon Insignia of Compliance-Manufacturer # M564
- Hawaii Compliant
Quality & innovation
What Our Clients Have To Say
I have been very busy installing boxes weekly and out of all the different brand names that I have been installing boxes weekly and out of all the different brand names that I have been installing your boxes are the best to install, top quality and very clean, its been very helpful on saving us time and labor during the install also makes me look good to the customers. Thank you!
I have been using Commercial cooling walk-ins for over 15 years and use their product in every design job, from consulting to quote and drawing they are absolutely the best in business, I have sold and install for 120 of their walk-ins.
I've been working with Commercial Cooling for a year and a half now and since moving a significant amount of custom work their way, we have seen dramatic improvements in the quality of our panel boxes, cost savings and lead times. From a sourcing standpoint, those are the three main characteristics I am looking for in a major supplier and Commercial Cooling has consistently executed all three. From the production floor to executive management, Commercial Cooling has been recognized as a superior supplier and partner from the higher quality standards to increased profitability in our products. Keep up the good work Commercial Cooling!
Your response time on drawings and quotes has improved markedly: you were already good, but you are now even better! Thank you for being an excellent company with a superior product: we appreciate you!!
I want to say how impressed we were with your operation and the helpfulness of yourself and everyone else at your facility.
Today is my 10 year Anniversary with Commercial Cooling. I signed the Contract on my Birthday 10 years ago today. I want to give thanks to both of you for the opportunity to Rep Commercial Cooling, because it has been a great Partnership. Commercial Cooling is the "Best" I Have ever Repped in my 30+ Years in Arizona.